All Models PORTION BLENDINGSYSTEMTMPortion Control Ice Shaver BlenderOwner’s ManualRead And Save These InstructionsFOODSERVICE
Each buttons factory Pre-Set Application.Use the following chart to determine which button you will need.NOTE:The chart below uses the factory setting
115a. When the blending cycle is complete, and more ice is needed, press and holdthe SHAVE ONLY button. By pressing the SHAVE ONLY button more ice wi
The Portion Blending SystemTMadvanced electronic controls can be custom programmed, byeither using the Control Panel or an optional programming chip,
135. With the display reading ‘ICE +01’press the ▲ select button toincrease the amount of ice to an increment of +05 and releasethe select button. NOT
14Retainer Nut Removal• The retainer nut is easily removed using a standard6” (15 cm) screwdriver.* Turn container upside downand insert screwdriver s
The PBS Shaving Blade is two blades in one. The blade has two shaving edges so that afresh edge can be exposed by simply rotating the blade 180˚. Your
Item#Description120/100V 220/240V752 752 64 oz. (2 L) - Container with ice blade, no lid assembly 755 755 Lid Plug (for Two Piece Lid)758 758 64 oz. (
#752#758#1151 or#1552#836#RBB502#802#1192#1551PLS504PLS503CST500RBB506PLS509PLS511#1550#1222#755#119117
Removing Ice from the Ice BinWARNING: To reduce the risk of injury unplug the unitbefore removing ice from the Ice Bin. Do not operate without lidin
CARE NOTE:Do not let mixtures, liquids and food products dry inside the container. Rinsethroughout use. Drying product may lock around the blade and w
21. Read all instructions.2. To protect against risk of electrical shock, do not put shaver base in wateror other liquid.3. Close adult supervision is
Ice Chute & Splash GuardRemove and separate the chute and guard from the Ice Bin, then wash in warm soapy water.Rinse clean under running water an
1. Problem:• Drinks not fully blended or haveimproper consistency.Solution:Change blending time or ice quantity. See page 12 for instructions.5. Probl
7. Problem:• Ice shaving too noisy, shaverfreezes up.Solution #1:Ice is too cold. Do not use bagged freezer ice.Use bin-stored or ice machine ice.Solu
23Portion Blending System:Height of unit: 27 1/2” H (69.85 cm)Additional height needed above machine for adding ice: 20” (50.8 cm)Shipping weight (pr
©2002 Vita-Mix Corporation. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, includ
17. The maximum capacity is equivalent to the ounces (liters) listed on thecontainer, i.e. 64 oz. (2 liters), 48 oz. (1.4 liters), and substantially l
4Ice Bin LidIce BinControl PanelLeveling Feet64 oz. (2 L)PolycarbonateContainerSplash GuardContainer PadIce ChuteIce ShelfShaver Base
5CONTINUED ON PAGE 6Setting Up The PBSPlace the PBS on a sturdy, level surface or counter. Packaged inside the Ice Bin are items necessary for the op
CONTINUED FROM PAGE 56Using the Drain Hose KitThe Drain Hose Kit contains one 90˚ elbow and two hoseclamps. When routing to a sink, bucket, or similar
7• Avoid using bagged ice that has been stored in a freezer at extremely low temperature.Use of this type of ice may result in freeze-up of the shaver
Portion Blending SystemTMON/OFF switch - Located on the back of the machine the ON/OFF switch controlsthe power to the PBS. With the machine plugged i
9SHAVE ONLY button - Allows the operator to add more ice after a shave/blend cycle or evenshave ice without the blender running. Press and hold the SH
Kommentare zu diesen Handbüchern